How to Install a Pocket Door
What is a pocket doorway? And how do you set up a pocket doorway? Discover the tips and methods for setting up a pocket doorway to help save ground area from a conventional hinged doorway swing. An fantastic solution for smaller areas or awkward doorway places.
For much more smaller area alternatives, consider these: Ideas to make a smaller area really feel open, our Foldable Craft Table, and a Tiny area homework or business office station.
Just before we show you how to set up a pocket doorway — let us solution the most typical issue:
What is a pocket doorway?
A pocket doorway is a sliding doorway on a track inside of the wall. Where by a sliding barn doorway and the barn doorway components are on the exterior of the wall, a pocket doorway and pocket doorway components are mounted inside of the wall and entirely hidden.
Concealed pocket doors are good alternatives for smaller areas and 50 % loos, due to the fact they help save the ground area from a conventional hinged doorway swing, even though nonetheless featuring much more privateness than a barn doorway. Pocket doors are also entirely hidden when open, so they don’t require any adjustment to your wall decor both.
Associated Reading: Do it yourself Barn Doors and Barn Door Hardware
For our pocket doorway set up, we experienced a 50 % bathtub at the finish of a hallway, with the doorway swinging out. We required a pocket doorway! You can see over how the doorway opened up into the hall and, with children, it was just normally open. Across the hall was our bedroom doorway, so it was blocked and the photos on the wall ended up only 50 % noticeable.
Not the look and really feel we ended up heading for (in particular with our new board and batten wainscoting around the household) and it was bad for the walking site visitors flow, so a pocket doorway was the way to go for us. I Very recommend a prebuilt pocket doorway package and here’s how the procedure goes:
How To Set up A Pocket Door
*Bear in mind, right before commencing any task that impacts the construction of your property be confident to talk to with a structural engineer or architect!*
Update March 2019: We mounted another pocket doorway in our present-day property and manufactured a video to show you the procedure! Test it out over on our YouTube channel:
Supplies and instruments for pocket doorway body installation
This post consists of affiliate hyperlinks. Discover much more and go through our comprehensive disclosure plan below.
Stage 1: Pick the location
This wonderful blank wall with no electrical or plumbing inside of manufactured the excellent place for a pocket doorway.
Stage two: Eliminate the existing doorway
Ahh… the difference it would make to choose off the doorway! The good detail about setting up a pocket doorway is that when you choose off the existing doorway, you can see exactly how the area will really feel when you are done: wonderful and open, no doorway blocking your path! 
Stage 3: Hold drop cloths
Just before commencing any demo, place up some drop cloths to have all. the. dust. (This drop cloth is hung in the area that shares the wall the pocket doorway is heading into.)
Stage four: Eliminate drywall
The pocket doorway will go in the wall that is in between the 50 % bathtub and our master bathroom shower, so we cut out the drywall on the 50 % bathtub facet quite cautiously (We even kept it in just one piece and reinstalled it! NO squander!). We scored the walls deeply at all the corners, then cut as a result of the other sections and used a crowbar to gently pop the nails out of the back again of the drywall (you can also use a reciprocating observed to cut the nails to get you started off).
Listed here is the substantial piece of drywall at the time removed…
Stage 5: Eliminate studs
Up coming, we eliminated the studs and header wherever the pocket doorway package will go. (We did not build a non permanent wall due to the fact this household has two parallel walls in 3 ft on both facet. If you do not have those supporting walls, you may need to have to assemble a non permanent wall right before eliminating the studs. Talk to a contractor, if required.)
We used a reciprocating observed to cut the nails so that the studs could be reused.
Stage six: Create a doorway body
Justin started off with a new header, and established the jack and king studs in position. (Jack signifies the just one supporting the header and the king is the comprehensive top stud that sits exterior the header.)
Stage 7: Increase the pocket doorway package
Now that the doorway framing is in position, the effortless portion is incorporating the pocket doorway package. Basically, it is a slot (pocket) with area for the doorway to slide into and a track on leading.
Use shims to make certain it sits in the good position.
Stage eight: Put together the existing doorway, if required.
Increase the track components to the existing doorway making use of the directions that appear with the pocket doorway package. Also take away the previous doorway knob and hinges and set up a take care of plug, if you need to have just one.
Stage nine: Hold the doorway
And the final success? Pocket doorway perfection… perfectly, almost!
It arrived at perfection when we mounted all the doorway trim and a wonderful coat of black paint to match the other doors!
Seem how open and unobstructed the area is now! I hung new household images when all the wainscoting and trim was up… really like it!)
If you want to see the first post about the 1/two bathtub check it out below!
You should comply with together with us on Pinterest, YouTube, Instagram and Fb.
And uncover much more good doorway tutorials, this sort of as:
Revealed Aug 22 2012 // Up-to-date Apr 20 2020
Associated
